Everyone has his or her own rationale on the subject of Tools You Need to Install a New Bathtub .
Setting up a tub isn't precisely rocket science, but it does require strong plumbing, woodworking, and also often, tiling skills. Changing an old bath tub with a brand-new one is likewise a moderately difficult task. If the old tub is readily obtainable, the project can relocate immediately; if you have to open up a wall to remove the old bathtub and place the new bathtub, the job is much harder. In either instance, the job is within a residence handyman's abilities, although you will require a helper to vacate the old tub and also set in the brand-new one. Make certain you have actually qualified on your own for the task and also are comfortable trying it. Rather than working with a contractor to take over a halfway-completed job, it is far better to consider employing one before you start. Chances are you may require a specialist plumber to make tube links.
This short article will certainly aid you install a new tub in your washroom if you have already gotten a brand-new bathtub and also don't need to alter the setup of your previous water pipelines.
Your devices and material checklist must make up the following:
Getting ready for the Installation
Firstly, the supporting structure provided with the bathroom needs to be fitted (if required) according to the supplier's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to ensure that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to now be ready to be suited its last position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the water system. After doing so, turn on the faucets to drain any kind of water staying in the system. The procedure of removing the existing faucets can be quite bothersome due to the limited access that is often the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a fabric all set for the staying water that will certainly come from the pipelines. Once the supply pipes have actually been removed, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Installing the Bath tub
Using the two wood boards under its feet, place the bath tub in the required setting. The wood boards are valuable in equally spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 tiny points.
The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the bath tub until the spirit level reviews degree.
To install faucets, fit all-time low of the furthest flexible faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the same for the other faucet.
Activate the water supply and inspect all joints and also brand-new pipework for leaks as well as tighten them if needed. Load the bath tub and likewise examine the overflow electrical outlet and the normal outlet for leakages.
Ultimately, deal with the bath paneling as described in the maker's user's manual. Tiling and also securing around the bath tub should wait until the tub has been utilized at least once as this will settle it right into its last setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin making sure that the washing machines remain in location between the tap and the sink. Secure the tap in position with the supplier given backnut. As soon as the faucet is safely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet ports. The former type should be attached to the faucet finishes first, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the area where the bathroom satisfies the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a rigid seal, causing the water to pass through the wall between the bathroom as well as the tiling, resulting in complications with wetness as well as possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your fixtures and fittings. They are marketed in tubes as well as cartridges, as well as are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of drenched newspaper or soft rope. Remember to constantly load the tub with water before securing, to enable the movement experienced when the bathtub remains in use. The sealant can split relatively early if you do not think about this activity before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily readily available on the market. It is suggested to fit the tiles making use of water-resistant or water resistant adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm just very focused on Tools You Need to Install a New Bathtub and I hope you appreciated the entire piece. Loved our article? Please share it. Let somebody else locate it. We appreciate reading our article about Tools You Need to Install a New Bathtub .
Schedule Appointment Now